The hazard of overloading the tanker
Vehicle overloading poses serious hazards to safe driving and transportation. It not only endangers the safety of one's own life, but also induces a large number of road traffic accidents, causing huge losses to the people's personal and property safety. Most road traffic accidents are caused by overloaded vehicles.
Tanker trucks are used as special vehicles for the transportation of petroleum derivatives. The items shipped are flammable and explosive. The first impression that may be given to everyone is that it will not be overloaded. After all, the can is closed and has a fixed volume. Is that realistic situation really like this?
In some petrochemical ports, in addition to standard-sized tank trucks , there are also vehicles that have obvious differences in appearance. The tanks on these vehicles are particularly large, and the amount of oil pulled is correspondingly large, but it greatly exceeds the maximum traction of the vehicle. This kind of tanker is very dangerous. Â Â Â Â Â Â Â Â Â
1. During the journey, the overloaded tanker will bring pressure on the road surface that exceeds the design load, which will greatly shorten the useful life of the road. When the bridge passes, it may break the bridge and increase the maintenance cost.
2. When the vehicle is overloaded, the braking distance becomes longer due to the increased mass, which increases the danger. If the overload is very serious, it may exceed the load of the tire and cause the tire to be deformed, causing sudden bursts of tires, deviations, and even accidents of overturning. If the tank falls, it will lose the protection of the static electricity device, because the colliding friction of the oil in the tank will cause static electricity and cause the consequences of explosion.
3. It is an illegal act to drive an overloaded vehicle, and the driver will have a psychological burden on the degree of incompatibility. Serious operational errors will occur, affecting traffic safety, causing traffic accidents and causing harm to others.
4. When the vehicle is overloaded, the speed will decrease and it will not reach the normal speed. Directly affected the patency of the road.
Penalties imposed for overloading are also more stringent:
According to the "Law of the People's Republic of China on Road Traffic Safety," the provisions of Article 61: If a motorized cargo vehicle exceeds the quality of an approved load or carries passengers in violation of regulations, it shall be punished by the motor vehicle driver according to the following provisions:
(1) A fine of 200 yuan shall be imposed if the quality of the approved load exceeds 30 percent;
(2) A fine of 500 yuan shall be imposed if it exceeds 30% of the quality of the approved carrier and is less than 50%;
(3) A fine of 1,000 yuan shall be imposed if it exceeds 50 percent or more of the quality of the approved carrier and is less than 100 percent;
(4) A fine of 2,000 yuan shall be imposed if it exceeds the approved quality of more than one hundred percent;
(5) A fine of 2,000 yuan shall be imposed if the passenger is carried in violation of the regulations.
CNC punching and shearing equipment for the processing of angles studied for small and medium size steel construction companies. These lines provide flexibility and simple use, and are characterized by an innovative infeed roller conveyor system allowing high precision with minimum loss of material.
Advantages:
- Versatile solution: each model can be configured according to the most diverse production lots and to customer requirement with an affordable investment.
- Compact frame for easy installation and reduced overall size.
- Remote diagnosis is possible through a network connection that allows our service team to perform routine checks
The linear tool carrier (y-axis) has several stations that hold the punching tools and one cutting tool. Especially for flexibility and efficient processing are setup times a crucial cost factor. Downtimes should be reduced to a minimum. Therefore, recent tool systems are designed for fast and convenient change of punches and dies. They are equipped with a special plug-in system for a quick and easy change of tools.
There is no need to screw anything together. The punch and die plate are adjusted to each other automatically Punches and dies can be changed rapidly meaning less machine downtime
Angle punching round hole and s-lot hole samples
The Punching Unit:
This
unit is consists of three pieces of machine body, two hydraulic pressure
punching cylinders, four die bases with upper and lower dies, and two sets of
servo systems for controlling stadia adjustment. This unit can be installed three
different standards punches on each side. Every punch matches with one gas
cylinder. The gas cylinder piston pole links a padding block, which installed
between punch poles and oil cylinder press head. It automatic chooses punch,
namely choose relevant gas cylinder to drive relevant padding block according
to the order of computer. The position of stadia is located by servo motor,
which drives ball screw to drive die base move up and down, thus to achieve the
requirement of stadia position. It can punch many rows and different diameters
holes on two wings of angle steel.
The Marking Unit:
New design for type marking unit, more stable and longer life
This
unit consists of fix lathe bed, movable lathe bed, hydraulic pressure head,
four positions oil cylinders (can change four positions for character boxes)
and adjusting device. According to the order of computer, to mark on places the
drawings require. For making the mark clear and endurable, and avoiding the
angle steel abrade character heads, it adds oil cylinder of movable lathe bed
uplift and falling. For satisfying the processing scope, it adds manual
adjustment setup, which can change the position of characters to adapt
different standards angle steel.
The Shearing Unit:
This unit consists of frame
machine body, hydraulic pressure dynamic cylinder, upper blade setup, lower blade
setup, and front bracket tank etc. The front bracket tank avoids angle steel to
strike lower blade. The lower blade setup can adjust the clearance according to
angle steel thickness to ensure the cutting quality. It cuts different
standards of angle steel, according to the order of computer.
The Feeding Conveyors:
Double linear guide and detection rack for total
feeding conveyor ensure better accuracy and machine stability. Linear guide
from Taiwan HIWIN.
The NC Feeding Carriage:
Newest NC carriage, linear guide drive, accuracy
and stability much better!
NC carriage linear guide cushion, pneumatic lift
Work Table And Overturning Rack:
Overturn
rack for loading material automatically
Angle Punching Marking Shearing Line
Angle Punching Marking Shearing Line,Angle Connecting Plate Punching,Punching Shearing And Marking Line,CNC Angle Production Line
Shandong Sunrise CNC Machine Co., Ltd , https://www.scmcnc.com