Mechanical elliptic gear flowmeter commonly used fault maintenance

Elliptical gear flow meter troubleshooting and analysis:
First, the gear may not rotate Possible causes:
1. Impurities fall into the table during installation, and the elliptical gear is stuck.
Measures: Re-install after washing and washing, press the mark marked by the oval gear Note: The new table is easy to occur, and the oval gear is placed according to the mark number.
2. The liquid to be measured is not clear and the filter is filled with impurities.
Measure: Wash the filter to remove impurities
3. The measured fluid pressure is too small.
Measure: Pressurize the second, the oval gear rotates but the pointer does not move Possible causes:
1. Drive wheel jamming measures: Remove impurities and add lubricant
2. Coupling gear loosening measures: Re-tighten gear 3. Shaking phenomenon when the pointer rotates. Possible cause: Excessive flow rate, exceeding the specified value. Measures: Adjust the flow rate to the specified value. 4. Irregular noise may occur when the oval gear rotates. : Flow is too large, exceeds the specified value Action: Adjust the flow to the specified value 5. Pointer reverses, character wheel reverse Possible cause: The direction of the liquid flow is opposite to the arrow marked by the case
Measures: Demolition, installation according to the direction of the direction Six, the error is too large, negative possible causes:
1. The flow is too small measures: change the smaller diameter flow meter
2. Bypass leakage measures: Check the bypass to prevent leakage
3. The service life is too long, the elliptic gear wears more measures: adjust the gear according to the error change value, the error is too large, and the positive difference may cause:
1. The gas contained in the liquid measures: install a gas separator in front of the watch and prevent leakage at the flange joint.
2. The meter checks the indexing of the word wheel after repair is not at the position of the pointer at "0", causing misreading measures: the position of the pointer when correcting the word wheel position
Remarks: Allocate gears to manufacturers, or send factory repairs
3. Viscosity of the liquid and the viscosity of the calibration liquid differ too much. Measures: Change the value of the error, change the gear Note: To the manufacturer to adjust the gear

Sample display:

After-sales and warranty

All products supplied by Duo Qin Instrument (Shanghai) Co., Ltd.:
All products are warranted for 2 years;
Provide free telephone consultation, guide installation and commissioning services;
Negotiate door-to-door installation, commissioning and other issues, and only charge reasonable travel expenses;
Large amount can be free to guide the installation, commissioning;

Service tenet: No matter how long the product is used, as long as you find us, we will solve all problems for you until you are satisfied. We believe that our experience in the flow meter industry for more than 10 years can bring you satisfactory service.

Note: The flow meter has many specifications, not a price product, different caliber, different configuration, the price is different, need to be based on your working conditions selection quote ~~~

Dochin Instrument (Shanghai) Co., Ltd. Main products: electromagnetic flowmeter, vortex flowmeter, turbine flowmeter, ultrasonic flowmeter, V-cone flowmeter, metal rotor flowmeter, oval gear flowmeter, ultrasonic cold heat meter and (Explosion-proof type) quantitative control system and other products, your needs and satisfaction is always our pursuit, welcome to call the communication consulting.

we are manufcatory and can supply the best price and good quality .

it  is full range of CYLINDER LINER  for the following type :

AAA) YANMAR DIESEL ENGINE     
K(D)L, KFL-T, 6MAL-H/T/HT/DT, S165-T/ST/EN,     
S185-ST/UT/ET, M200L-UN/SN/EN/M220L-UN/SN/EN / N 330 

     
BBB) DAIHATSU DIESEL ENGINE     
PS22/26/ DS18(A)/ DS(B)22/

DL20/22/28/ DK20   / DK 28 
     
CCC) NIIGATA DIESEL ENGINE     
 6L(M)25BX/6M28AFTE/BX/6M31X/EZ/EX/  31AFTE  /34AGT   
     
DDD) AKASAKA      
AH30/AH38/ AH40/D/F/  A31/34/37/41/ DM28/30/33/36/38/40(A)K/ DM46/  UEC37H-HB/ UEC 37/88H     
UEC 37LA/ UEC45LA/ UEC52LA/ UEC52HA/ UEC60HA/  UEC60LS/ UEC45HA/115 ALL UET TYPE     
     
EEE) MITSUBISHI    (KOBE AND AKASAKA ) 
45/75C/ 45/80D/ 52/90D/ 52/105D.E/

UEC37H-IIB/ UET37/88HA/UEC45HA.LA/ UEC52HA.LA/ S6B/      
ETC     
     
FFF) HANSHIN     
6LU(D)26/ 6LU(N)28A/ 6LU(D)32/6LU(D)35/ 6LU(S)38/ 40 / 6LU40/ 6LU46A/ 6LU50A/

6EL30/ EL(S)32     /6EL(S)35/ 6EL38/ 6EL40/ 6EL(S)44/50A/     

GGG) MAN B&W     
S35MC/L35MCE/L50MCE/ L60MCE/ 40/54A     
     
HHH) MITSUBISHI PURIFIER     
SJ700~SJ1800/SJ 2000


III)SULZER 

 RND 68 RND 76 RD 44



JJJ) MAKITA

GSLH – 633 637                 KSLH -633 637



Kkk) PIELSTICK

PC 2-5  PC 2-6


Engine Cylinder Liner

Engine Cylinder Liner,Engine Part Cylinder Liner,Diesel Engine Liner,Cylinder Liner For Ship,Cylinder Liner For Diesel Engine

ZhouShan HeCheng Machinery Co., LTD. , http://www.hcmarineparts.com